Airbag control unit with part number 1328447080

What is the function of the airbag control unit 1328447080?

The airbag control unit with part number 1328447080 is a control module manufactured by TRW/Siemens-BOSCH for the occupant restraint system. It is specifically designed for vehicles such as the Peugeot Boxer, Citroën Jumper, and the equivalent Fiat Ducato (platform 244), where it processes signals from crash sensors and deploys airbags and seatbelt pretensioners in the event of a collision.

As a central component of the safety system, this ECU continuously monitors all connected sensors, airbag modules, and seatbelt pretensioners. The electronics check system readiness at every vehicle start-up and ensure that all components are functioning correctly. It is also known under alternative designations such as 13 284 470 80, as well as related manufacturer part numbers like 5WK43154 or 5WK43157, which are used in the same vehicle context.

Why does the control unit 1328447080 fail?

The most common causes of failure for the control unit 1328447080 are internal electronic malfunctions and permanently stored crash data following an accident. Defective semiconductors, memory chips, or voltage regulators can result in error codes such as B0100. Communication issues caused by faulty CAN transceivers or specific ground connection faults on the housing (B0102) are also typical.

A primary source of failure is the storage of crash data in the internal memory (EEPROM/Flash). After deployment, the control unit locks down operation and cannot be reset using workshop diagnostic tools. This is a safety feature that requires electronic repair to selectively erase the data.

In addition, age-related defects may occur in electronic components. These include cold solder joints at connectors, faulty voltage regulators, or defective driver circuits responsible for controlling peripheral devices. A specific fault is error code B0102, indicating a poor ground connection on the ECU housing, often caused by corrosion or contact resistance.

Communication errors on the CAN bus, indicated by error codes such as U0019 or U1703, are frequently rooted in the hardware of the control unit itself—for example, due to a defective CAN transceiver chip.

How do you recognize a defect in the control unit 1328447080?

A defect in the control unit 1328447080 primarily manifests as a permanently illuminated airbag warning light (SRS light) in the instrument cluster. Often, no diagnostic communication can be established with the control unit, or non‑erasable error codes such as “B0100 – Internal Error” remain stored in the fault memory.

The most noticeable symptom is the persistently lit airbag warning light, even when no accident has occurred. This is frequently accompanied by a message on the display urging you to visit a workshop, such as “Check Airbag.”

Another clear indication is when a diagnostic tool cannot access the airbag control unit. The workshop is unable to read or clear error codes because the communication unit within the device has failed.

Following an accident, crash data remains stored in memory and cannot be cleared using standard diagnostic equipment. The system stays locked, and the warning light continues to illuminate until the data is removed through specialized repair procedures.

In which vehicles is the control unit 1328447080 installed?

The airbag control unit 1328447080 is predominantly installed in commercial vehicles from the PSA Group and its partner manufacturers. At Airbag24, this control unit is repaired for models such as the Peugeot Boxer IV and the Citroën Jumper I (model years 1994–2002). The equivalent Fiat Ducato on platform 244 also uses this ECU.

At Airbag24, professional repair services for the control unit 1328447080 are offered for the following models:

Peugeot: Boxer IV (based on platform 244)

Citroën: Jumper I (1994–2002)

Fiat: Ducato (platform 244, identical to PSA models)

How does the repair process work at Airbag24?

The repair of the control unit 1328447080 begins with a precise incoming inspection upon receipt at Airbag24. Depending on the nature of the fault, crash data is erased from memory, defective electronic components such as processors or voltage regulators are replaced, and cold solder joints are reworked. Following successful restoration, a functional test is conducted on a test bench.

Before removal, a diagnosis should be performed at a workshop to rule out external faults in wiring, sensors, or seatbelt pretensioners. After dismantling, the control unit is securely packaged and shipped to Airbag24.

At Airbag24, technicians analyze the electronics at the component level. This includes reading the memory, checking the power supply, and repairing communication pathways. An advantage of this repair is that the original vehicle coding and chassis number are preserved, eliminating the need for time-consuming reprogramming.

After the repair is completed and all functions have been verified, the unit will be returned. It can usually be reinstalled without additional coding; only the vehicle’s fault memory needs to be cleared. All repairs are covered by a 12-month warranty.

What shipping options does Airbag24 offer?

To send your defective control unit to Airbag24, you can either drop it off yourself free of charge or arrange a convenient UPS pickup at your preferred location. For the return shipment, several options are available, including free standard UPS shipping, faster UPS Express shipping, or in‑store self‑pickup.

For the outbound shipment, you have the choice: send the package to us yourself or use the UPS pickup service, where the package will be collected from an address of your choosing.

The following options are available for returning the repaired unit:

Free standard UPS shipping (delivery in 1–3 business days)

UPS Express shipping (delivery in 1–2 business days)

Standard UPS shipping with cash on delivery (delivery in 1–3 business days)

UPS Express shipping with cash on delivery (delivery in 1–2 business days)

In‑store self‑pickup