Airbag control unit with part number 1610617380

What is the function of the airbag control unit 1610617380?

The airbag control unit with part number 1610617380 is the central control module for the passive safety system in the Peugeot Bipper I (2007–2015). It continuously analyzes data from crash sensors and is responsible for precisely and rapidly deploying airbags and seatbelt pretensioners in the event of a collision. Additionally, it stores accident-related data (crash data).

As the “brain” of the restraint system, this component ensures optimal protection for occupants. It monitors all connected components, from front and side airbags to seat occupancy sensors.

Compatibility also extends to similar models from Citroën, such as the Berlingo, where it may be found under alternative part numbers like 9803917380 or 59001158. The core functionality remains identical.

Why does the control unit 1610617380 fail?

A failure of the control unit 1610617380 is most commonly caused by stored crash data following an accident, which locks out further functionality. Other causes include internal electronic defects in components, as well as damage from moisture ingress or water damage that can lead to short circuits on the circuit board.

After a collision, the control unit permanently stores crash data in its internal memory. This is a manufacturer‑imposed safety measure that locks the system and requires a diagnostic check. In such cases, the unit isn’t defective in the traditional sense but must be professionally reset.

Beyond accidents, electronic components such as processors or memory chips can wear out or suffer damage from voltage spikes, resulting in internal malfunctions that prevent proper operation.

Ingress of moisture—often due to a leaking windshield or bodywork—is another critical source of failure. Moisture causes corrosion and short circuits in the sensitive electronic components on the circuit board.

How do you recognize a defect in the airbag control unit 1610617380?

A typical defect of the control unit 1610617380 manifests as a constantly illuminated or flashing airbag warning light on the dashboard. Often, no communication can be established with the control unit using a diagnostic tool, with specific error codes such as 106F being logged. Even after replacing airbags, the system remains inactive.

The clearest warning sign is the airbag light, which no longer extinguishes as usual after starting the engine. It may remain lit continuously or, in some cases, stay on steadily after a brief delay—typically around 30 seconds.

A professional workshop often finds during diagnosis that the control unit is unresponsive. Attempts to read the fault memory fail because no connection can be established. Error code 106F specifically indicates an internal issue within the control unit.

An additional clear symptom appears after an accident: even though all deployed components—such as the knee airbag, driver’s airbag, or passenger airbag—have been expertly replaced, the fault cannot be cleared and the warning light stays on. This is due to the stored crash data.

In which vehicles is the control unit 1610617380 installed?

The part number 1610617380 is primarily used in the first-generation Peugeot Bipper (Type I), produced between 2007 and 2015. Due to close technical similarities within the PSA Group, technically identical control units can also be found in Citroën models, such as the Berlingo.

At Airbag24, we specialize in repairing this control unit. We service part number 1610617380 for the following model:

Peugeot: Bipper I (model years 2007–2015)

It’s important to note that cross-referenced part numbers like 9803917380 or 59001158 may point to the same or a very similar control unit installed in related vehicles.

What are the benefits of repairing 1610617380?

The key advantage of repair lies in substantial cost savings—up to 70% compared to purchasing a new unit, which can cost up to €800 depending on the manufacturer. Repair is also a sustainable solution that preserves the vehicle’s original configuration. You receive 2 years' statutory liability for defects on the completed repair.

Rather than investing in an expensive new part, refurbishment offers a cost-effective alternative. Full functionality of the original control unit is restored, making it an equivalent solution.

Since the original control unit is repaired, there’s no need for time-consuming coding or programming work on the vehicle—tasks often required when installing a new or used replacement. The repaired unit can typically be reinstalled immediately.

Repairing not only saves your budget but also protects the environment. By reusing the component, valuable electronic waste is avoided and resources are conserved.

How does the repair process work at Airbag24?

At Airbag24, the repair process begins with the professional removal and safe shipment of your defective control unit 1610617380. Our technicians perform a precise diagnosis, fix any internal faults or erase stored crash data, and conclude the process with a functional test. You will receive your fully operational control unit back, backed by 2 years' statutory liability for defects.

Before removal, it is advisable to have a diagnosis performed at a specialized workshop to confirm that the fault lies in the control unit itself and not in peripheral components (e.g., wiring harness, sensors). Please include the diagnostic report with your shipment.

Upon receipt at Airbag24, the control unit undergoes a thorough analysis. Specialized technicians inspect the circuit board for electronic defects, moisture damage, or faulty solder joints, and reset the memory if crash data has been stored.

Each repair step is meticulously documented. Following successful restoration and final quality control, the control unit is prepared for return shipment.