Airbag control unit with part number 46 19 680

What is the function of Airbag Control Unit 4619680?

The airbag control unit with part number 4619680 is the central control module of the occupant restraint system (SRS) for the Saab 900 II NG (1993–1998). It processes data from crash sensors to precisely and promptly deploy airbags and seatbelt pretensioners in the event of an accident, thereby ensuring passive vehicle safety.

As an original OEM part—often supplied by Bosch (e.g., under part number 0285001089)—this module is responsible for monitoring all safety‑related components of the airbag system. It continuously checks the functionality of sensors, ignition circuits, and internal electronics.

Compatibility has also been verified under the alternative Saab part number 5266564. Proper operation of this control unit is critical, as a malfunction can disable the entire restraint system, leaving occupants unprotected in an emergency.

Why does control unit 4619680 fail?

The most common cause of failure for control unit 4619680 is stored crash data after an accident, which prevents further use. Additional faults arise from internal electronic issues due to aging, moisture, or voltage surges, leading to total failure or communication problems.

Even after minor rear‑end collisions that trigger seatbelt pretensioners, the control unit stores what’s known as a “crash lock.” This lock cannot be cleared using standard workshop diagnostic tools, making specialized repair essential to reactivate the module.

Hardware defects on the circuit board are also prevalent. Aging components, damaged solder joints, or corroded traces caused by moisture can result in internal malfunctions. These often manifest as error code 65535, directly indicating a faulty control unit rather than an issue with external components such as sensors or wiring.

Interrupted communication due to defective connectors or CAN‑bus errors can likewise render the control unit inoperable. A professional diagnosis should always determine whether the fault lies within the control unit itself or in peripheral components.

How do you recognize a defect in control unit 4619680?

A defect in control unit 4619680 primarily shows up as the airbag warning light permanently illuminated or flashing intermittently on the Saab 900’s dashboard. Another clear symptom is the lack of communication with diagnostic equipment or the presence of persistent error codes that cannot be cleared, such as “internal control unit failure.”

The most obvious sign is the constantly lit airbag warning light, signaling a critical system error that could prevent airbags and seatbelt pretensioners from deploying during an accident.

Another frequent symptom is complete loss of communication: when a workshop attempts to read the fault memory, they find no access to the SRS module, pointing to severe internal hardware damage.

If error codes like 65535 (“control unit failure”) or messages about stored crash data appear and cannot be reset, the root cause is clearly in the control unit itself. Even if external components, such as the coil spring, have already been replaced and the fault (e.g., driver airbag) persists, suspicion naturally falls on the control unit.

In which vehicles is control unit 4619680 installed?

The airbag control unit with part number 4619680 was specifically designed for the second generation of the Saab 900 (NG), produced from 1993 to 1998. It appears across various trim levels of this model series. At Airbag24, we repair this module for all applicable models.

At Airbag24, control unit 4619680 is repaired for the following specific Saab models:

Saab 900 II NG (model years 1993–1998)

Saab 900 S

Saab 900 SE

Saab 900 Convertible

Saab 900 Talladega

Due to its safety‑critical function, it is imperative that only a control unit with the exact same part number be used during replacement to ensure full compatibility with the vehicle’s system.

How is control unit 4619680 professionally repaired?

Professional repair of the 4619680 control unit at Airbag24 includes a detailed analysis of the electronics, proper deletion of stored crash data, and restoration or replacement of defective components on the circuit board. Finally, full functionality is verified through a simulation test.

After submitting the removed control unit to Airbag24, the repair follows a proven procedure. First, an initial inspection is conducted to confirm the reported fault and read the internal fault memory.

The core process is component-level repair. Technicians open the module and analyze the circuit board. Depending on the fault pattern, crash data is erased using specialized programming tools, defective microchips are replaced, or cold solder joints are re-soldered.

Subsequently, the refurbished control unit undergoes a comprehensive functional test on a simulation bench. Here, real‑world vehicle operation is simulated to ensure the module communicates flawlessly and correctly activates all outputs. We provide a 12‑month warranty on every repair.

What shipping options does Airbag24 offer?

Airbag24 provides flexible and secure shipping options. You can either send your defective control unit back at no cost yourself, or arrange a convenient UPS pickup at your preferred location. For return shipping, we offer free standard shipping as well as faster express options, both available with cash-on-delivery.

For sending your unit to us, you have two free options: you can ship the package yourself, or use the UPS pickup service, which collects the control unit directly from your address.

For returning the repaired unit, we offer the following options:

UPS Standard Shipping (1–3 business days) – Free of charge.

UPS Express Shipping (1–2 business days)

UPS Standard Shipping with Cash-on-Delivery (1–3 business days)

UPS Express Shipping with Cash-on-Delivery (1–2 business days)

In addition, you can choose to pick up the repaired unit in person at our facility.