Airbag control unit with part number 50511356

What is the function of Airbag Control Unit 50511356?

The airbag control unit with part number 50511356 is the central control module of the occupant protection system in the Alfa Romeo Brera 939. It analyzes data from acceleration and crash sensors to precisely deploy airbags and seatbelt pretensioners in the event of a collision, while also storing relevant fault and crash data.

As the “brain” of the restraint system, this module continuously monitors signals from peripheral sensors, including acceleration sensors for collision detection, as well as sensors on seatbelt pretensioners and seat occupancy detectors.

In an emergency, the control unit sends ignition pulses to the corresponding airbag and seatbelt pretensioner units. At the same time, all relevant events—especially crash data—are permanently stored in its internal memory (EEPROM/Flash) to enable post‑crash analysis.

Why does control unit 50511356 fail?

A failure of control unit 50511356 is often caused by crash data retained in memory after an airbag deployment, which prevents further use. Other causes include electronic defects in internal SMD components such as capacitors, power supply paths, or the memory chips themselves.

The most common cause of malfunction is the storage of crash data. After a collision where airbags or seatbelt pretensioners have deployed, the control unit locks itself for safety reasons and must be repaired or replaced.

In addition, purely electronic faults can occur on the circuit board. These include damage to SMD components responsible for power supply, defective fuse resistors, or errors in the Flash or EEPROM memory chips that hinder proper operation.

A visual inspection may occasionally reveal external damage, such as corroded contacts at connectors or even burn marks on the board, indicating a serious internal defect.

How do you recognize a fault in 50511356?

A typical sign of a defective airbag control unit 50511356 is the permanently illuminated airbag warning light on the instrument cluster. Often, communication with the control unit via a diagnostic tool becomes impossible, or non‑erasable fault codes remain stored in the error memory.

The clearest symptom is the persistently lit airbag warning light. It does not turn off after starting the vehicle, indicating a system‑critical fault in the restraint system.

Another clear indication is when a workshop cannot establish communication with the airbag control unit using a diagnostic device. The module fails to respond to queries, making accurate fault diagnosis impossible.

In cases where communication is still possible, fault codes are often stored that cannot be cleared. Typical entries point to an internal control unit error or a stored “crash event.”

Before removing the control unit, external sources of error should be checked. Faulty connectors—especially under the seats—, a defective clock spring in the steering wheel, or a faulty seatbelt buckle switch can produce similar symptoms.

In which vehicles is control unit 50511356 installed?

The airbag control unit with part number 50511356 is specifically used in vehicles manufactured by Alfa Romeo. At Airbag24, we professionally repair this module for the Alfa Romeo Brera 939 model series, produced between 2006 and 2010.

At Airbag24, we specialize in repairing this control unit for the following specific models:

Alfa Romeo Brera 939 (model years 2006–2008)

Alfa Romeo Brera 939 Facelift (model years 2008–2010)

How does the repair of 50511356 proceed at Airbag24?

After sending the removed control unit 50511356 to Airbag24, our technicians perform a comprehensive incoming inspection. The repair includes clearing crash data, replacing defective SMD components, and conducting a final functional test. We provide a 12‑month warranty on every repair.

For quick and efficient diagnosis, we recommend reading out the error memory before removal and attaching the fault log to your package. This significantly speeds up the testing process at our facility.

Upon receipt at Airbag24, a careful visual inspection is carried out to detect mechanical damage or corrosion, followed by reading the internal memory to document fault codes and crash data.

The actual electronic repair focuses on addressing the root cause. Stored crash data is reset in compliance with applicable legal requirements. Defective components such as voltage regulators, capacitors, or memory chips (EEPROM/Flash) are professionally replaced at the chip level.

Upon completion of the repair, a comprehensive functional test is performed to ensure flawless communication and operation of the control unit. In some cases, after reinstallation, adaptation to the vehicle identification number (VIN) or re‑coding within the vehicle may be required.

What shipping options are available at Airbag24?

You can send your defective control unit to us free of charge or arrange a convenient UPS pickup. For return shipping after repair, we offer free standard UPS delivery as well as faster express options. Both methods are also available with cash on delivery.

For sending your package to us, you have two choices: you can either ship it yourself at no cost and bring it in personally, or request a UPS pickup from your preferred location.

After successful repair, we will promptly return the control unit to you. You can choose from several options:

Standard UPS shipping is free for you. For faster delivery, UPS Express shipping is available.

Both standard and express shipping can, upon request, be combined with cash on delivery. Alternatively, personal collection at our premises is also possible.