Airbag control unit with part number 5Q0 959 655 AS

What is the function of the Airbag Control Unit 5Q0 959 655 AS?

The Airbag Control Unit 5Q0 959 655 AS is the central control unit of the Supplemental Restraint System (SRS) in vehicles based on the MQB platform, such as the VW Golf 7. It processes data from crash sensors in real time, deploys airbags and seatbelt pretensioners in the event of a collision, and continuously performs self-diagnosis of the entire system.

As the “brain” of the passive safety system, it receives signals from front and side acceleration sensors, seatbelt contact switches, and seat occupancy detectors. Based on this information, the control unit determines within milliseconds which restraint devices need to be activated and at what intensity to provide optimal protection for occupants.

In addition, the unit communicates via the CAN bus with other critical control units, such as the ABS or ESP, to exchange vehicle data. After a crash, it stores relevant crash data for later analysis. If faults are detected or following a crash, it illuminates the airbag warning light on the instrument cluster.

What types of defects occur in the 5Q0 959 655 AS?

The most common causes of failure for the 5Q0 959 655 AS control unit are stored crash data after an accident that locks the device, as well as internal electronic malfunctions. A typical error code indicating such a fault is B2000 – Control Unit Fault. Similar fault patterns also appear in related MQB part numbers like 5Q0 959 655 A, AB, AR, BH, or CC.

Even after a crash—when only seatbelt pretensioners have been deployed—the control unit writes an irreversible crash record into its internal memory. This lockout ensures safety and requires professional data reset procedures.

Hardware failures represent another frequent cause. These include memory issues (Flash/EEPROM), malfunctions in the microcontroller itself, or problems with the driver stages responsible for triggering the airbags. Internal voltage regulators can also fail, disabling the entire unit’s functionality.

Rarely, external factors such as moisture, corrosion at connector contacts, or voltage spikes in the vehicle’s electrical system may lead to failure. Improper coding can likewise result in malfunctions, though these are usually correctable.

How do you recognize a defect in the 5Q0 959 655 AS control unit?

A malfunction of the Airbag Control Unit 5Q0 959 655 AS almost always manifests as a permanently illuminated airbag warning light on the dashboard. Often, a text message such as “Airbag or SRS Error” appears on the instrument cluster display as well. With this active fault, the vehicle will fail the main inspection.

When reading the fault memory using a diagnostic tool, specific error codes are displayed. Common entries include “B2000 – Control Unit Fault” or “Internal Error.” Following a crash, the entry “Crash Data Stored” is typical and cannot be cleared by standard workshop testers.

Another clear symptom is when the control unit becomes completely inaccessible through the diagnostic port. The tester then reports “No Communication with Airbag Control Unit.” In some cases, the vehicle identification number (VIN) stored in the control unit may also appear invalid or blank.

Since the airbag control unit is integrated into the vehicle’s CAN bus network, its failure can, in rare instances, cause sporadic malfunctions in other systems communicating over the same data bus.

In which vehicles is the 5Q0 959 655 AS installed?

The Airbag Control Unit with part number 5Q0 959 655 AS is primarily installed in Volkswagen vehicles built on the MQB platform. At Airbag24, we specialize in repairing this control unit, particularly for the Volkswagen Golf 7. Our repair methods are transferable to other MQB models equipped with similar control units.

Specifically, this control unit is used in the following model:

Volkswagen: Golf 7 (AU / 5G series)

How does the repair of the 5Q0 959 655 AS proceed?

Repair at Airbag24 follows a standardized process that begins with an initial inspection of the removed control unit. Depending on the nature of the fault, either the stored crash data is professionally erased or defective electronic components on the circuit board are replaced. Finally, full functionality is verified on a test bench.

Before removal, a specialized workshop should read out the fault memory and inspect the peripherals (cables, connectors, sensors) to rule out other potential sources of failure. In the Golf 7, the control unit is typically located near the center console and must be removed after disconnecting the battery.

Upon arrival at Airbag24, an analysis is performed. If only crash data is present, it is deleted from the internal memory (EEPROM/Flash) using specialized software. The control unit then functions again as if it were new.

For hardware failures, such as error code B2000, defective components like driver ICs, voltage regulators, or memory chips are professionally desoldered and replaced with new, high-quality parts. A functional test is performed after each repair. You receive a 12-month warranty on the completed repair.

What shipping options are available?

For fast and hassle-free processing, you can send your defective control unit to Airbag24 free of charge or use the convenient UPS pickup service. For returning your repaired unit, you have access to free UPS standard shipping, as well as optional express services or cash-on-delivery payment.

Shipping to Airbag24:

You can either ship the package yourself at no cost or arrange for UPS to pick it up from your preferred location. Personal drop-off at our facility is also possible.

Return shipping to you:

UPS standard shipping (1–3 business days) is free of charge. Alternatively, you can choose UPS express shipping (1–2 business days), cash-on-delivery (standard or express), or self-pickup.