Airbag control unit with part number 89170-0H110

What is the function of the airbag control unit 89170-0H110?

The airbag control unit with part number 89170-0H110 is the central control module for the passive safety system in the Toyota Aygo AB10 series, as well as in platform‑related models from Citroën and Peugeot. It analyzes data from the acceleration sensors and decides within milliseconds whether to deploy airbags and seatbelt pretensioners.

As the “brain” of the restraint system, this unit is responsible for optimally protecting occupants in the event of a collision. It continuously monitors all connected components—such as the various airbags, seat‑occupancy detectors, and seatbelt pretensioners—for proper functionality.

Any system faults, whether caused by an internal defect or an external interference, are detected by the control unit and indicated by the illumination of the airbag warning light on the instrument panel.

Why does the airbag control unit 89170-0H110 fail?

The most common causes of failure for the 89170-0H110 control unit are internal electronic defects that often occur even without an accident, as well as stored crash data following a collision. These block the device’s functionality and cannot be cleared using standard workshop diagnostic tools. Hardware malfunctions that disrupt communication are also typical.

A primary issue is internal circuit board failures, where electronic components such as processors or memory chips fail. This often happens due to age-related wear and can result in total failure or sporadic malfunctions.

After a crash—even at low activation thresholds—crash data is securely stored in the control unit’s memory. This lockout prevents further use and requires specialized hardware‑level reprogramming to reset it.

These fault patterns also appear in identical or related part numbers like 89170-0H010, 89170-0H020, 89170-0H050, and 89170-0D210, since they share similar technical foundations.

How do you recognize a fault in the 89170-0H110 control unit?

A defective 89170-0H110 control unit typically manifests as a permanently or intermittently illuminated airbag warning light on the dashboard. Additionally, communication via the OBD interface may no longer be possible, and non‑erasable fault codes remain stored in the error memory.

The most obvious sign is the activated airbag warning light. It fails to extinguish after engine start-up or flashes irregularly during driving, indicating a safety‑critical system error.

Another clear symptom is complete loss of communication. The workshop cannot establish a connection to the airbag control unit using diagnostic equipment, making fault diagnosis impossible.

In some cases, erroneous data may also be read out—for example, a missing vehicle identification number or implausible error messages regarding seemingly intact components such as seat‑occupancy mats or seatbelt pretensioners.

Important note: Using simulators or resistors to disable the warning light is life‑threatening and results in the revocation of the vehicle’s operating permit. Repairing the control unit is the only safe and legally permissible solution.

In which vehicles is the 89170-0H110 control unit installed?

The airbag control unit 89170-0H110 is the original equipment manufacturer (OEM) part number for the first‑generation Toyota Aygo (AB10) throughout its entire production run. Due to the shared platform, it is also used in the sister models Citroën C1 and Peugeot 107.

At Airbag24, we repair this control unit for the following specific models and series:

Toyota: Aygo AB10 (2005–2009), Aygo AB10 First Facelift (2009–2012), Aygo AB10 Second Facelift (2012–2014)

Additionally, repairs are available for equivalent control units in the corresponding Citroën (C1) and Peugeot (107) models, which share the same technical foundation.

How does the repair of the 89170-0H110 control unit work?

Professional repair at Airbag24 offers a safe and cost‑effective alternative to expensive new parts. After removal and shipment, the unit undergoes electronic analysis, defective components are replaced, and stored crash data is erased. The control unit is then reprogrammed and fully restored to working condition.

Once you have removed the control unit and packed it securely, send it to Airbag24. Ideally, include a printout of the diagnostic report to expedite fault analysis.

Our technicians perform an initial inspection and begin targeted repair procedures. This includes erasing crash data, resetting the software to factory settings, and replacing faulty hardware components on the circuit board. The goal is to restore the unit to a condition indistinguishable from a new part.

After successful repair and a final functional test, the control unit is ready for reinstallation (plug-and-play). In most cases, only clearing the fault memory in the vehicle is required after reinstallation. Every repair comes with a 12-month warranty.

What shipping options does Airbag24 offer?

For fast and convenient processing, Airbag24 provides flexible shipping options. You can either send your defective control unit yourself or arrange for UPS pickup at your preferred location. Return shipping is free via UPS Standard or optionally via Express, including cash-on-delivery.

For outbound shipping, you have two choices: send the package to us at your own expense, or use our convenient UPS pickup service, where the package is collected directly from your premises.

For return shipping after repair, the following options are available: free UPS Standard shipping, faster UPS Express shipping—both also with cash-on-delivery—and personal self-collection on-site.