Airbag control unit with part number 95910-09001

What is the function of Airbag Control Unit 95910-09001?

The airbag control unit with part number 95910-09001 is the central control module of the passive safety system, specifically designed for the SsangYong Stavic A200 (2013–2019). It continuously analyzes data from crash sensors and determines, within milliseconds, whether to deploy airbags and seatbelt pretensioners.

As an original equipment manufacturer (OEM) part, this ECU (Electronic Control Unit) serves as the brain of the entire restraint system. It monitors not only the sensors but also the ignition circuits of individual airbag modules and seatbelt pretensioners. In the event of a collision, it ensures the correct activation sequence to provide optimal protection for occupants.

In addition, the control unit performs a self-test every time the vehicle is started. If any system faults are detected during this test, the airbag warning light on the instrument panel illuminates to alert the driver.

Why does control unit 95910-09001 fail?

The most common cause of failure for control unit 95910-09001 is the storage of crash data after a collision. This internal lockout is a safety feature. Other defects arise from general electrical disturbances that can lead to communication loss or complete system failure.

Following an accident in which airbags or seatbelt pretensioners have deployed, the control unit permanently writes crash data into its internal memory. This locks the module and prevents further use until the data is professionally erased. This is not a software error but rather an intentional hardware-level lock.

Electrical malfunctions—such as voltage fluctuations in the vehicle’s electrical system or moisture ingress—can also cause internal board failures. These often manifest as the control unit becoming unresponsive. Repair focuses on eliminating these electronic faults and restoring the original functionality. The variant with part number 95910-09000 is technically very similar and exhibits the same fault patterns.

How do you recognize a defect in 95910-09001?

A defect in control unit 95910-09001 primarily manifests as a constantly illuminated or intermittently flashing airbag warning light. Often, communication with the control unit via a diagnostic tool becomes impossible, and after an accident, the unit is locked and no longer readable.

The clearest symptom is the active airbag warning lamp. Instead of extinguishing after a few seconds upon engine start-up as expected, it remains steadily lit or begins to flash, signaling a serious fault in the restraint system.

Another clear indication is a complete loss of communication. When a workshop attempts to read the fault memory through the OBD interface, the control unit fails to respond, becoming unreachable to the diagnostic tool.

After an airbag deployment, the control unit is locked. Although the warning light stays on, specific fault codes often cannot be retrieved because the crash-data lockout blocks normal diagnostic access. Faults suggesting defective passenger-side airbags, crash sensors, or seat-mounted airbags may also point to an internal issue with the control unit itself.

In which vehicles is 95910-09001 installed?

The airbag control unit with part number 95910-09001 is exclusively used in SsangYong vehicles. At Airbag24, we specialize in repairing this module—as well as the 95910-09000 variant—for the SsangYong Stavic A200, produced between 2013 and 2019.

The assignment of this OEM part number is highly specific. At Airbag24, repairs are offered for the following model:

SsangYong Stavic A200 (model years 2013–2019)

Compatibility with models from other manufacturers is not guaranteed, even if their part numbers sound similar.

How is 95910-09001 repaired?

At Airbag24, repairs follow a professional process: Upon receipt, the 95910-09001 control unit undergoes an initial inspection. The core of the restoration involves erasing crash data and fixing electronic faults. After a successful final test, the unit is returned ready for installation, complete with 2 years' statutory liability for defects.

Before removal, a diagnosis using an OBD device is recommended to confirm that the fault truly lies within the control unit. Subsequently, the removed module is securely packaged for transport back to Airbag24.

Our technicians analyze the electronics and restore the unit. The focus is on addressing the root cause—whether it’s recovery from a crash-data lockout or repairing damaged components on the circuit board. Following repair, the control unit undergoes a functional test to verify proper operation.

The repaired unit is returned as a “plug-and-play” solution. No complicated re-coding or programming in the vehicle is required. We provide 2 years' statutory liability for defects on every repair.