Airbag control unit with part number 95910-0X112

What is the function of the airbag control unit 95910-0X112?

The airbag control unit with part number 95910-0X112 is an original Hyundai OEM safety module, primarily installed in the Hyundai Xcent of the BA series (2014–2022). As the central SRS control unit, it manages the entire occupant protection system, processes signals from crash sensors, and ensures timely deployment of airbags and seatbelt pretensioners.

This component serves as the brain of the vehicle’s passive safety system. It continuously monitors all connected sensors—such as acceleration and pressure sensors—to activate the appropriate restraint systems within milliseconds in the event of a collision. After a crash, the unit stores so‑called crash data, which prevents reactivation until it is professionally cleared.

Why does the control unit 95910-0X112 fail?

The most common cause of failure for the 95910-0X112 control unit is stored crash data following an accident, which locks the system and prevents further use. Additional defects arise from electronic component failures, such as faulty capacitors or sensor ICs, as well as moisture damage. Often, only individual components are affected, allowing for repair.

A key reason for failure is the permanent storage of crash data. This lockout is intentionally implemented by the manufacturer to mandate a system check after a crash. Without clearing this data, the airbag warning light remains illuminated, and the system becomes inoperable.

In addition, internal hardware faults may occur, including board defects, cold solder joints, or failure of specific microchips responsible for signal processing. Such electronic issues can impair the control unit’s functionality even without a prior collision.

It’s important to note that variants like 95910-0X100, 95910-0X101, 95910-0X110, and 95910-0X120 are closely related or interchangeable and may exhibit similar fault patterns. The underlying causes of failure are often identical across these models.

How do you recognize a defect in the 95910-0X112?

A defective 95910-0X112 control unit typically manifests as a permanently lit or flashing airbag warning light (SRS lamp). Another hallmark is the unit’s inability to communicate with diagnostic tools. Specific error codes such as B1060 (internal fault) or errors related to side and seat airbags also indicate a malfunction.

The most obvious sign is the persistently illuminated airbag warning light on the instrument cluster. It may remain steadily lit, stay on briefly after engine start, or flash intermittently—signaling that the safety system is not operational.

An additional clear symptom is the lack of communication with the control unit. When a workshop attempts to read the fault memory via the OBD interface, no response is received from the airbag module. This frequently occurs when crash data has been stored, locking the device.

The fault memory may contain specific codes directly pointing to an internal defect in the control unit. These include errors such as B1060 (internal software/firmware fault) or messages indicating malfunctions in particular components—like side or seat airbags—even if those mechanical parts are intact.

In which vehicles is 95910-0X112 installed?

The airbag control unit 95910-0X112 is mainly used in Hyundai vehicles. At Airbag24, we repair this control unit, along with compatible variants such as 95910-0X100 or 95910-0X110, specifically for Hyundai Accent and Xcent models manufactured during the specified production years.

Specifically, this part number is relevant for the following models and series:

- Hyundai Xcent (BA series), model years 2014–2022

- Hyundai Accent (often identical to the Xcent)

Since related part numbers—including 95910-0X100, 95910-0X101, 95910-0X110, and 95910-0X120—are also repaired, our service covers a broad range of these vehicle models. A precise verification of the part number on the removed unit ensures compatibility.

How is the 95910-0X112 professionally repaired?

At Airbag24, repairing the 95910-0X112 follows a proven process. Upon receipt, technicians analyze the unit at the component level, erase stored crash data, and reset the firmware. Defective parts, such as capacitors or ICs, are expertly replaced, and final functionality is thoroughly tested. You receive a 12-month warranty on the repair.

The repair process aims to fully restore the original functionality. First, an initial inspection identifies the exact fault. Then, using specialized equipment, the stored crash data that locks the system is safely removed.

In the next step, electronic repair is performed at the component level. Defective components such as capacitors, processors, or memory chips (ICs) identified as the cause of the fault are desoldered and replaced with new, high-quality parts. Finally, the device’s firmware is reset or updated if necessary.

After refurbishment, each control unit undergoes a comprehensive functional test. During this process, communication with diagnostic systems is verified, and it is ensured that the airbag warning light correctly extinguishes after installation. This guarantees the full functionality of the safety system.

Is Repairing 95910-0X112 Worth It?

Repairing the airbag control unit 95910-0X112 offers significant cost savings compared to purchasing a new part, which can range from 200 to 500 euros depending on the supplier. Since the original unit remains intact, no re-coding is required for your vehicle. Additionally, Airbag24 provides a 12-month warranty on the repair.

A key advantage is the substantial cost reduction—often exceeding 70%—compared to a new Hyundai part. Repair represents an economically sensible alternative that restores full safety without straining your budget.

Because the vehicle-specific original control unit is repaired, there is no need for time-consuming reprogramming or coding at the workshop. The refurbished unit can typically be reinstalled using a plug-and-play approach, saving both time and expenses.

What Shipping Options Are Available at Airbag24?

You can either ship your control unit to Airbag24 free of charge yourself or arrange a convenient UPS pickup at your preferred location. Returns are equally flexible: choose between free standard UPS shipping, faster UPS Express shipping, or cash-on-delivery. Self-collection is also available.

For sending your unit, you have two simple options: either securely pack the removed control unit and send it at your own expense, or use UPS’s convenient pickup service, which collects the package directly from your home or workshop.

Upon successful repair, the control unit is securely repackaged and shipped back to you. By default, we offer free standard UPS shipping. For urgent cases, faster options like UPS Express shipping are available. Both methods can also be arranged with cash-on-delivery, allowing you to pay only upon receipt of the item. Alternatively, you may pick up the unit in person at our facility.