Airbag control unit with part number BP4K-57K30B

What is the function of the BP4K-57K30B airbag control unit?

The BP4K-57K30B is the original airbag control unit, also known as the SAS Unit, for the Mazda 3 BL series (2009–2013). It serves as the central control module for the entire occupant protection system, processing signals from crash sensors and activating the airbags and seatbelt pretensioners in the event of a collision.

As an original Mazda component, this control unit is precisely matched to the vehicle architecture of the Mazda 3 BL. It is responsible for monitoring and controlling all relevant SRS components (Supplemental Restraint System).

The module’s physical installation location is in the vehicle’s center tunnel, directly beneath the cupholder and next to the handbrake. From there, it is centrally connected to all sensors and actuators of the airbag system.

Why does the BP4K-57K30B airbag control unit fail?

The most common causes of failure for the BP4K-57K30B include water damage due to its mounting position, general electronic malfunctions on the circuit board, or stored crash data following an accident. The latter can lock the control unit, preventing further use even if there is no visible physical damage.

A major cause of malfunction is the storage of crash data in the control unit’s internal memory. After an airbag deployment, the module is internally locked to prevent improper reuse. This condition cannot be cleared using standard diagnostic tools.

Additional defects may arise from water damage or electronic component failures. In particular, the EEPROM memory chip—specifically the M95640W type—can be affected. Repair in such cases requires direct access to this chip to erase the data or replace the chip entirely. Similar repair methods apply to related part numbers such as BCF1-57K30, BFB6-57K30, and BFD1-57K30.

How do you recognize a defect in the BP4K-57K30B?

A defect in the BP4K-57K30B control unit primarily manifests as a permanently illuminated airbag warning light on the instrument cluster. Additionally, specific fault codes can be read from the vehicle’s diagnostic memory, indicating either an internal fault within the control unit or stored crash data.

The most obvious sign is the red SRS or airbag warning light that remains on after the engine starts. This indicates that the safety system is not operational and would not deploy correctly in the event of a crash.

During a workshop diagnosis, the control unit may refuse communication with the diagnostic tool or display error codes suggesting an unerasable internal fault or “crash data stored.” These findings typically confirm the need for repair or replacement.

In which models is the BP4K-57K30B installed?

The airbag control unit with part number BP4K-57K30B is used exclusively in the Mazda 3 BL series. At Airbag24, we repair this module for both the first-generation BL model and the subsequent facelift version, produced during the specified model years.

At Airbag24, the BP4K-57K30B part number is professionally refurbished for the following vehicles:

Mazda:

• Mazda 3 BL (model years 2009–2011)

• Mazda 3 BL Facelift (model years 2011–2013)

How is the BP4K-57K30B professionally repaired?

At Airbag24, the BP4K-57K30B is repaired through targeted analysis and restoration of its electronics. Stored crash data is erased at the chip level from the EEPROM (M95640W), and any hardware defects are rectified. Following successful testing, the control unit is fully functional and ready for reinstallation.

After being sent to Airbag24, the control unit undergoes a standardized repair process. First, an initial inspection identifies the exact nature of the fault. Subsequently, stored crash data is deleted via direct access to the memory chip—a highly specialized procedure requiring specialized equipment.

If the defect is due to an electronic issue or water damage, the affected components on the circuit board are identified and expertly replaced. Once repairs are complete, the module is tested on a bench to ensure flawless operation across all systems. We provide a 12-month warranty on every repair.

Important note on reinstallation

To ensure safe functionality, the manufacturer‑specified installation procedure must be strictly followed after repair or replacement:

1. Install all other SRS components (airbags, seatbelt pretensioners, sensors) and their wiring first.

2. Completely disconnect the vehicle battery.

3. Securely mount the airbag control unit in its installation position and fasten it with tools (do not rely solely on hand-tightening).

4. Firmly connect all connectors to the module.

5. Only as a final step, reconnect the vehicle battery.

What shipping options are available at Airbag24?

To send your defective control unit to Airbag24, you can either deliver it yourself free of charge or arrange for a UPS pickup. For returning the repaired unit, you have access to free standard UPS shipping as well as faster express options, including cash-on-delivery.

You have two convenient ways to ship your defective control unit to us. You can either send the package yourself or bring it in person. Alternatively, you can schedule a UPS pickup from your preferred location.

After the repair is completed, we offer several return shipping options:

• Free standard UPS shipping

• UPS express shipping for faster delivery

• Standard UPS shipping with cash-on-delivery

• UPS express shipping with cash-on-delivery

• Personal pickup at our premises