Airbag control unit with part number MD166255

What is the function of the airbag control unit MD166255?

The airbag control unit with part number MD166255 is the central control unit for the occupant protection system in the Mitsubishi Eclipse D20 (model years 1990–1995). It monitors the sensors, deploys the airbags and seatbelt pretensioners in the event of a crash, and stores relevant crash data that can lock the system after deployment.

Technically speaking, this control unit—also known as the SRS module (Supplemental Restraint System)—is the brain of the passive safety system. It continuously collects and processes data from the crash sensors distributed throughout the vehicle to detect an impending collision.

In the event of a crash whose severity exceeds predefined thresholds, the MD166255 sends ignition signals to the corresponding airbags and seatbelt pretensioners. At the same time, crash data is recorded in the device’s internal memory, which subsequently locks the system, necessitating repair or replacement.

Why does the MD166255 control unit fail?

The primary cause of failure for the MD166255 control unit is stored crash data following airbag or seatbelt pretensioner deployment, which prevents further operation. Additional defects arise from age-related wear of electronic components such as chips or capacitors, water damage, corrosion, or electrical faults like short circuits and reverse polarity during jump-starts.

The most common cause is the accumulation of crash data. After a crash, the control unit deliberately locks itself to prevent unintended re‑deployment and to force a full system check. This lock often cannot be reset by workshops and requires specialized electronic repair.

Furthermore, age‑related defects may occur in electronic components on the circuit board. Internal errors, frequently indicated by fault codes such as B1209, U1XXX, or B1XXX, point to faulty processors, memory chips, or sensors within the control unit itself.

External factors, such as moisture from water damage, can lead to corrosion on connectors and traces. Electrical disturbances—such as reverse polarity during a jump-start or short circuits in the vehicle’s electrical system—can also irreparably damage the control unit’s sensitive electronics.

How do you recognize a defect in the MD166255?

A defective MD166255 control unit primarily manifests as a permanently illuminated or flashing airbag warning light on the dashboard. Additionally, communication with diagnostic equipment often becomes impossible, and error codes stored in the fault memory—such as internal SRS errors—cannot be cleared. As a result, the entire airbag system is deactivated.

The most obvious sign is the activated airbag warning light, indicating to the driver that the entire restraint system is non‑functional and will not provide protection in the event of a crash. An immediate visit to a workshop is therefore essential.

Another clear symptom is the loss of diagnostic capability. When a workshop attempts to read the fault memory via the OBD interface, the control unit refuses to communicate. Neither reading nor clearing fault entries is possible at that point.

Even if communication remains possible, certain fault codes—indicating an internal defect or stored crash data—cannot be permanently erased. They reappear immediately after an attempt to clear them, confirming the defect within the control unit itself.

In which vehicles is the MD166255 installed?

The airbag control unit with part number MD166255 was specifically developed for the first-generation Mitsubishi Eclipse. At Airbag24, repairs for this particular control unit are available for the model listed below and are performed regularly to restore full functionality of the safety system.

Our expertise in repairing this specific part number covers the following vehicle model:

Mitsubishi Eclipse D20 (model years 1990–1995)

What are the benefits of repairing the MD166255?

Repairing the MD166255 control unit offers significant cost savings of up to 90% compared to purchasing a new unit, which can cost as much as €750. The repaired unit is ready for immediate installation, and its functionality is backed by a 12‑month warranty, making it the most economical solution.

The financial advantage is the decisive factor. Rather than investing in an expensive new component, repair provides a budget‑friendly yet technically sound alternative. The original vehicle configuration remains intact, eliminating the need for complex coding or adjustments.

Moreover, repair is a sustainable solution. Rather than discarding a complex electronic component, it is expertly refurbished. This conserves valuable resources and prevents electronic waste. Each completed repair comes with a 12-month warranty.

How does the repair process work at Airbag24?

At Airbag24, repairing the MD166255 begins with a comprehensive diagnosis to verify the fault. Next, the stored crash data is erased, and the unit is reset to factory settings. If necessary, defective electronic components are replaced. Following a final test and with a 12-month warranty, the control unit is returned to you.

The process starts after removing the control unit from the vehicle. Before shipping, we recommend reading out the fault memory and attaching the diagnostic report to expedite fault analysis. The removed unit is securely packaged and sent to Airbag24.

Upon receipt, our technicians perform a thorough analysis. The core of the repair involves erasing the crash data from the internal memory and resetting the software. In cases of hardware defects, damaged components such as chips, capacitors, or sensors are replaced with new, high-quality parts.

Finally, each repaired control unit undergoes rigorous functional testing on specialized test benches. Only after all tests have been successfully passed is the unit cleared for return shipment. The customer receives a fully functional component backed by a 12-month warranty.

What shipping options are available?

You can send your defective control unit to Airbag24 free of charge or arrange for UPS pickup. For the return shipment after repair, several options are available: free standard UPS shipping, faster UPS Express shipping—both also available with cash-on-delivery—and the option of in-person collection on-site.

For the outbound shipment, you can either mail the package yourself or conveniently use the UPS pickup service, which collects the package directly from your home or workshop, saving you the trip to the post office.

After the repair is complete, choose the return shipping method that suits you best. Standard UPS shipping is free. If you need the component back particularly quickly, we offer UPS Express shipping. Both options are also available with cash-on-delivery. Alternatively, you can pick up the repaired control unit in person at our facility.