What is a Dodge Viper ZB I airbag control unit?
The Dodge Viper ZB I airbag control unit is the central safety unit in the vehicle, responsible for activating the airbags and seatbelt pretensioners in the event of an accident. It continuously monitors all relevant sensors, stores important crash data, and thus ensures optimal occupant protection through precise control of the restraint systems.
This module, also called Occupant Restraint Controller (OCR), is the core of the passive safety system of your Dodge Viper ZB I (model years 2003-2010).
Based on acceleration and impact data, it decides which airbags and belt tensioners need to be deployed to protect occupants in the event of a crash.
Why is the Dodge Viper ZB I airbag control unit defective?
A Dodge Viper ZB I airbag control unit can be defective because it stores crash data after an accident and is then disabled for safety reasons, or because internal electronic components such as capacitors or processors fail due to age or overvoltage. Water damage caused by moisture ingress can also lead to corrosion and module failure.
After an airbag is deployed, the control unit saves a crash data record, which requires a reset for further use.
Internal errors in the control unit can also manifest themselves without an accident, which is then usually indicated by the airbag warning light in the cockpit.
A defective control module must be repaired or replaced immediately to restore full functionality of your Dodge Viper's airbag system.
Common error codes for Dodge Viper ZB I airbag control unit repair
During a Dodge Viper ZB I airbag control module repair, specific error codes indicate problems directly related to the control module's internal function or communication, such as airbag deployment circuit failures or internal memory errors. These codes are crucial for accurately diagnosing the faulty module.
- B1000 → Control unit communication error → Internal defect or loss of communication of the airbag ECU.
- U0151 → Occupant Restraint Controller reports no communication → Loss of communication between the airbag control unit and the vehicle network.
- ACM 1 → Internal error in the acceleration sensor module → A defect in the internal acceleration sensor of the airbag control unit.
- AECM 2 → Stored Energy Logic Module Error → Problem with the internal logic or energy storage of the airbag control module.
- AECM 3 → Driver side stored energy error → Internal error in the power supply or deployment circuit for the driver airbag.
- AECM 4 → Passenger side stored energy fault → Internal fault in the power supply or deployment circuit for the passenger airbag.
- Driver Squib Circuit Open → Error: Driver squib ignition circuit open → Open circuit in the circuit that deploys the driver airbag.
- Driver Squib Circuit Shorted → Error: Driver squib ignition circuit shorted → Short circuit in the circuit that deploys the driver airbag.
- Passenger Squib Circuit Open → Error: Passenger squib ignition circuit open → Open circuit in the circuit that deploys the passenger airbag.
- Passenger Squib Circuit Shorted → Error: Passenger squib ignition circuit shorted → Short circuit in the circuit that deploys the passenger airbag.
What part numbers are available for the Dodge Viper ZB I airbag control unit repair?
For Dodge Viper ZB I airbag control module repair, the primary original OEM part numbers 4865582AB and 4865582AC are the correct references, which come directly from Mopar and are approved for 2003–2006 (Gen 3 / ZB I) models. Knowledge of these part numbers is essential for a successful repair or replacement.
These Mopar part numbers are designed for the third generation Dodge Viper (ZB I) and represent the correct OEM airbag control units.
Some other numbers like 4848802AE or 68303219AA are relevant for older or later Viper models and are not directly intended for the ZB I series from 2003-2010.
For a precise Dodge Viper ZB I airbag control module repair, you should make sure that your module part number matches one of these numbers.
The relevant and verified OEM part numbers for the Dodge Viper ZB I airbag control unit are:
- 4865582AB → Manufacturer: Mopar → Type: Original/OEM (for Dodge Viper Gen 3, 2003–2006)
- 4865582AC → Manufacturer: Mopar → Type: Original/OEM (for Dodge Viper Gen 3, 2003–2006)
Both part numbers are directly compatible with the Dodge Viper ZB I model series and have been confirmed by Mopar.
If your airbag control unit is broken, professional diagnosis and repair is key to restoring vehicle safety.